vgkitboard_237xs/radio/sx126x-board.h

/*
  ______                              _
 / _____)             _              | |
( (____  _____ ____ _| |_ _____  ____| |__
 \____ \| ___ |    (_   _) ___ |/ ___)  _ \
 _____) ) ____| | | || |_| ____( (___| | | |
(______/|_____)_|_|_| \__)_____)\____)_| |_|
    (C)2013 Semtech

Description: SX126x driver specific target board functions implementation

License: Revised BSD License, see LICENSE.TXT file include in the project

Maintainer: Miguel Luis and Gregory Cristian
*/
#ifndef __SX126x_ARCH_H__
#define __SX126x_ARCH_H__

#include "sx126x.h"
#include "stdint.h"
void HAL_Delay_nMS(uint32_t time_ms);
/*!
 * \brief Initializes the radio I/Os pins interface
 */
//void SX126xIoInit( void );

/*!
 * \brief Initializes DIO IRQ handlers
 *
 * \param [IN] irqHandlers Array containing the IRQ callback functions
 */
//void SX126xIoIrqInit( DioIrqHandler dioIrq );

/*!
 * \brief De-initializes the radio I/Os pins interface.
 *
 * \remark Useful when going in MCU low power modes
 */
//void SX126xIoDeInit( void );

/*!
 * \brief HW Reset of the radio
 */
void SX126xReset( void );

/*!
 * \brief Blocking loop to wait while the Busy pin in high
 */
void SX126xWaitOnBusy( void );

/*!
 * \brief Wakes up the radio
 */
void SX126xWakeup( void );

/*!
 * \brief Send a command that write data to the radio
 *
 * \param [in]  opcode        Opcode of the command
 * \param [in]  buffer        Buffer to be send to the radio
 * \param [in]  size          Size of the buffer to send
 */
void SX126xWriteCommand( RadioCommands_t opcode, uint8_t *buffer, uint16_t size );

/*!
 * \brief Send a command that read data from the radio
 *
 * \param [in]  opcode        Opcode of the command
 * \param [out] buffer        Buffer holding data from the radio
 * \param [in]  size          Size of the buffer
 */
void SX126xReadCommand( RadioCommands_t opcode, uint8_t *buffer, uint16_t size );

/*!
 * \brief Write a single byte of data to the radio memory
 *
 * \param [in]  address       The address of the first byte to write in the radio
 * \param [in]  value         The data to be written in radio's memory
 */
void SX126xWriteRegister( uint16_t address, uint8_t value );

/*!
 * \brief Read a single byte of data from the radio memory
 *
 * \param [in]  address       The address of the first byte to write in the radio
 *
 * \retval      value         The value of the byte at the given address in radio's memory
 */
uint8_t SX126xReadRegister( uint16_t address );

/*!
 * \brief Sets the radio output power.
 *
 * \param [IN] power Sets the RF output power
 */
void SX126xSetRfTxPower( int8_t power );

/*!
 * \brief Gets the board PA selection configuration
 *
 * \param [IN] channel Channel frequency in Hz
 * \retval PaSelect RegPaConfig PaSelect value
 */
uint8_t SX126xGetPaSelect( uint32_t channel );

/*!
 * \brief Initializes the RF Switch I/Os pins interface
 */
void SX126xAntSwOn( void );

/*!
 * \brief De-initializes the RF Switch I/Os pins interface
 *
 * \remark Needed to decrease the power consumption in MCU low power modes
 */
void SX126xAntSwOff( void );

/*!
 * \brief Checks if the given RF frequency is supported by the hardware
 *
 * \param [IN] frequency RF frequency to be checked
 * \retval isSupported [true: supported, false: unsupported]
 */
bool SX126xCheckRfFrequency( uint32_t frequency );

/*!
 * Radio hardware and global parameters
 */
extern volatile SX126x_t SX126x;

#endif // __SX126x_ARCH_H__